If you purchased an EggRider from BGB after 25th April 2021 then your EggRider should be plug n play.

  1. Simply remove your RAD display and keypad and install the EggRider.
  2. Press and hold the ‘mode’ button for about 8 seconds to switch between on-road and off-road modes.
The BGB EggRider is speed-limited.
 
ON-ROAD speed limit is 25kph (15.5mph). The throttle limited to 6kph (4mph)
PAS 1 = 20% of 25kph (5kph / 3mph)
PAS 2 = 40% of 25kph (10kph / 6mph)
PAS 3 = 60% of 25kph (15kph / 9mph)
PAS 4 = 80% of 25kph (20kph / 12mph)
PAS 5 = 100% of 25kph (25kph / 15.5mph)
 
OFF-ROAD speed limit is +45kph (+20mph). The throttle is unlimited.
PAS 1 = 20% of 45kph (9kph / 5.5mph)
PAS 2 = 40% of 45kph (18kph / 11mph)
PAS 3 = 60% of 45kph (27kph / 16mph)
PAS 4 = 80% of 45kph (36kph / 22mph)
PAS 5 = 100% of 45kph (45kph / 28mph)
 
On-road produces max 6 amps – roughly 288 watts.
Off-road produces 19 amps – roughly 912 watts (this can and might peak up to 23 or 24 amps!)

Please, click here and take the time to thoroughly review the manual

iOS
Android
BGB Firmware

Note: You will need to download the entire BGB firmware zip file to your phone so that you can update the firmware on your EggRider.

  • With your new BGB firmware loaded, turn your EggRider off.
  • Press the mode and power button for about 5 to 8 seconds to load the BGB firmware settings. You will see DEF SETTINGS LOADED in the top left corner and the BGB logo flash up to confirm the default settings have been loaded.

The BGB firmware settings assume a 20-inch wheel and MPH speed setting. If you wish to change this you will need to download the EggRider app for your phone. Follow the steps below to install the EggRider app.

iOS App Download

Android App Download

Shop name: big game bikes (start typing the word big and then select Big Game Bikes from the drop down)
Order id: ‘your BGB order number’

The BGB firmware settings assume a 26-inch wheel and MPH speed setting. If you wish to change this you will need to download the EggRider app for your phone.

Follow these easy steps to update your EggRider to suit your wheel and speed preference.

  1. Assuming you have the BGB firmware, switch your EggRider off.
  2. Press and hold the mode and power button for about 8 seconds until you see ‘DEF SETTINGS LOADED’. This loads the BGB default settings which assumes 26 inch wheel and MPH speed.
  3. Connect your EggRider to the app.
  4. Wait for the display to switch to the dashboard then tap the 3 horizontal lines on the right.
  5. Tap the 3 horizontal lines on the top left and select DISPLAY SETTINGS.
  6. Press READ
  7. Now update the PREFERRED UNITS and WHEEL CIRCUMFERENCE to suit your bike.
  8. Press WRITE
  9. Tap the 3 horizontal lines on the top left and select LISHUI.
  10. Press READ
  11. Now update the WHEEL SIZE suit your bike.
  12. Press WRITE.
  13. Press the ORANGE power button to turn off your EggRider which saves your new settings.

That’s it! You’re done.

Note: Press and hold the MODE button for about 8 seconds to switch between ON and OFF road modes.